290 different careers — and it means something different in each. Maintenance for a Boiler Chemical Treatment Technician is not maintenance for a Boiler Operator. Below, the real task it carries in every job, with a ready AI prompt for each.
290careers do this work
456prompts that speak it
40attested by the job's own software
The maintenance, job by job
Same artifact, different stakes — each card is one career's real use of it, with its prompt.
Boiler Chemical Treatment Technician — Perform routine maintenance on machinery
Perform the scheduled maintenance round on Boiler A4: drain and inspect the chemical feed pump, replace the worn gaskets on the dosing line, calibrate the inline conductivity probe, record readings and sign off before shift end Wednesday.
Boiler Operator — Perform routine maintenance on machinery
Perform the scheduled lubrication, belt tension, and alignment checks on the feedwater pump and economizer, replace worn seals found, record torque and oil samples, and create a maintenance work order if vibration exceeds limits.
Boom Operator — Tend auxiliary equipment such as water treatment and refrigeration units, and heat exchangers.
Inspect and service the refrigeration unit room: check coolant pressure, clean strainers on the water treatment skid, verify heat exchanger delta-T is within 8–12°C, log the maintenance task and raise a work order if bearings run hot.
Building Services Coordinator — Take corrective action on issues
Document the three fault reports from Tower A, assign corrective actions to Ahmed and Maria with target completion dates next Tuesday and Thursday, log parts ordered and labour hours, and notify procurement if costs exceed the monthly maintenance budget.
Diesel Mechanic — Follow green operational practices involving conservation of water or energy or reduction of solid waste.
Implement water and energy savings on the shop floor this week: capture wash water for reuse, switch compressors to auto-stop, segregate scrap rubber for recycling, and log measures and savings in the maintenance record for review Friday.
Carry out the planned preventive maintenance on the packaging line: change filters, top up hydraulic oil, replace worn belts, run the start-up sequence, note torque readings and any anomalies in the maintenance record, and raise parts requests for anything consumed.
Enter today's preventive checks for Line 2 into the maintenance log: runtime hours, voltage and current readings, parts replaced, and any anomalies; attach uploaded photos of wear and sign off with my technician ID before the end of shift.
Lubricate the winch bearings, sliding guides and gear shafts on the AC motor assembly with the approved synthetic grease until free play is eliminated, wipe excess, record lubricant type and quantity in the maintenance log before returning unit to service by Friday.
Elevator Mechanic — Keep service records of maintenance tasks
Complete today's service record for Building 27: list each maintenance action, parts replaced, measurements taken, serial numbers, and safety checks; file it in the maintenance system and email the signed copy to facilities manager Carla Ruiz before leaving site.
Farm Equipment Technician — Clean and lubricate parts.
Strip parts from the combine header, clean bearings and sprockets, apply the specified grease to grease points, replace the air filter, note torque values and parts replaced, and close the job with updated service hours in the maintenance record.
Fuel Station Manager — Resolve equipment malfunctions
Fix the pump and dispenser faults reported on forecourt bay 2: diagnose the leak and pressure sensor error, record root cause and parts needed, schedule the technician and a safety shutdown, and update the maintenance log before 5pm today.
Run the evening collection route checklist, capture global positioning for the missed bin on Hargreaves Avenue, record the load weight and crew, and append the exception to the truck maintenance and route record.
Complete the weekly maintenance on Pump A: change seals, replace worn hoses, torque motor terminals to spec, bleed the system, verify pressure and flow, and file the repair log with parts used and time spent.
Put control measures in place for the maintenance team entering Tank C: establish clean routes, issue disposable coveralls and respirators per the hazard assessment, set decon station at the exit, and log each worker's entry and exit times at shift change.
Clean the east reading room windows, sills and woodwork this afternoon: remove loose dust, wash glass with streak‑free solution, wipe window frames and polish the wood ledges, note any paint damage in the maintenance book before 5pm.
Carry out repairs on the Unit 3 governor linkage: isolate the unit, replace worn pins and bearings per the assembly drawing, torque fasteners to spec, function-test governors under slow-roll, then update the repair record and close the maintenance job.
Strip and bench-test the dimmer racks after the show, replace any failed triac or module, record serials and firmware, and update the maintenance log so the chief electrician can sign off before the next load-in.
Replace burnt or flickering light bulbs in guest rooms and corridors during my shift; verify correct bulb type and wattage, safely change fixtures, record the location and replacement in the maintenance log, and report any non-working fittings.
Maintenance Technician — Perform maintenance and repair
Complete the planned maintenance on Pump P12: isolate and lockout, replace worn seal and O-rings, test motor amp draw and vibration, restore pressure to setpoint, then write the complete repair narrative and parts used into the pump's service log before end of shift.
Mechanic — Adjust and maintain industrial machinery, using control and regulating devices.
Adjust the conveyor drive regulators on the No.3 crusher, set control parameters to maintain 1200 rpm under load, log the changes in the maintenance register, and run a 30-minute load test to confirm stable operation.
Metro Operator — Operate auxiliary equipment as needed
Operate auxiliary pumps, blowers and compressors as required during the morning shift, respond to abnormal vibrations or temperatures, log actions and readings in the maintenance ledger, and inform the shift supervisor before leaving the plant area.
Repair any chafed stitching or broken stitching on sails and secure splices in running rigging, document parts used and time spent in the maintenance record, and advise the bosun if the sail must be taken down for full repair.
Operations Supervisor Transport — Resolve equipment malfunctions
Log the failed conveyor drive in the maintenance record, list observed fault codes and symptom timeline, assign a technician with parts on site, set priority to emergency, and request a field inspection before the 0800 shift handover tomorrow.
Do the scheduled equipment walk at Station 7: inspect compressor mounts, leak detectors, relief valves and suction filters, record condition and part numbers on the maintenance sheet, take photos of wear, and open a work order for anything needing repair with Maintenance Planner Tony Ruiz.
Plant Manager — Ensure compliance with safety regulations
Run the safety compliance checklist for the plant, verify that isolation permits and lockout tags are in place for today's planned work, review recent incident trends for root causes, and issue a compliance memo with corrective actions to HSE and the maintenance supervisor before shift change.
Post Production Coordinator — Supervise daily operations
Run the morning shift roster, confirm crew assignments for the boilers and feed pumps, check all required certifications are on file, and circulate the duty schedule with the maintenance lead and control room before 0700.
Recycling Plant Supervisor — Repair faults in equipment
Diagnose the conveyor motor fault at Line 3, record the fault code and parts needed, schedule the maintenance crew for an immediate repair window, and update parts reservation so the mechanic has the motor coupling and bearings before they start.
Site Supervisor — Ensure turbines operate efficiently
Run a performance sweep of each turbine for the last seven days, highlight machines below expected Cp and note pitch or yaw faults, create a short corrective-action list for the maintenance crew by 0900 Monday.
Telescope Maintenance Technician — Enter information into computer to copy program or to draw, modify, or store schematics, applying knowledge of software package used.
Enter the updated wiring layout and part serial numbers into the maintenance database, attach the revised schematic drawings and test logs, verify entries match the physical rack, then save and close the record before the end of shift.
Coordinate repair work on Turbine 17: confirm approved scope with the crew lead, schedule crane and technician windows, log permit-to-work start and expected completion in the maintenance log, and notify the grid operator of planned downtime.
Climb turbine 7 tonight with Lars, isolate the machine, follow the lockout plan, remove the faulty gearbox access panel, replace the failed pitch bearing per manufacturer procedure, run torque checks, and update the maintenance ticket with parts used and hours before handing back to operations.
Account Manager — Maintain records pertaining to inventory, personnel, orders, supplies, or machine maintenance.
Maintain the maintenance and supplies log for Site 4: record last service dates, outstanding orders, personnel on-call, and next scheduled inspections, flag any overdue machine maintenance and notify maintenance lead Carlos today.
Accounting Manager — Maintain records pertaining to inventory, personnel, orders, supplies, or machine maintenance.
Update the combined maintenance and personnel log with yesterday’s machine service, assigned technician, spare parts used, and expected next service date; attach the incident report summary and notify maintenance supervisor Jorge and payroll by end of day.
Acoustic Engineer — Enhance overall system performance
Collect last quarter's installed-system measurements, compare them to design targets, list the three worst-performing zones with suggested corrective actions and estimate expected improvement in decibels and STI for the maintenance team by Friday.
Aerospace Engineer — Write technical reports or other documentation, such as handbooks or bulletins, for use by engineering staff, management, or customers.
Draft the maintenance bulletin for the fuel line routing change: describe the engineering rationale, steps for field modification, required tooling and safety precautions, and submit the draft to reliability and the service bulletin board by Thursday.
Record the preventive maintenance checks I performed on the centrifuge and spectrophotometer, log serial numbers and calibration readings, schedule required service within 30 days if any reading falls outside tolerance, and circulate the maintenance note to the lab supervisor today.
Aircraft Cleaner — Lubricate machinery, vehicles, or equipment or perform minor repairs or adjustments, using hand tools.
Apply light oil to hinges and bearings, tighten loose fittings with a wrench, replace a worn brush or belt if needed, and log the minor repair with parts used so the maintenance record stays current.
Aircraft Maintenance Engineer — Repair electrical or mechanical equipment
Restore the #2 generator control unit on Airbus A320 VH-FLM: isolate electrical bus, replace damaged contactor, torque connections to spec, bench-test the unit and update the maintenance log with parts used and test results by 1600 today.
Aircraft Mechanic — Diagnose mechanical issues in aircraft
Troubleshoot the intermittent hydraulic pressure drop on A320 N890CD: review the maintenance history and schematics, perform pressure isolation and leak checks, bench-test suspected valves, capture test readings, and write a fault report with probable cause and next steps.
Airframe And Powerplant Technician — Diagnose mechanical issues in aircraft
Isolate the nosewheel shimmy report by reproducing the fault on taxi runs, inspect steering linkage and torque arms to blueprint tolerances, trace play to the worn bearing, document findings and recommend bearing replacement to the maintenance planner by noon.
Strip and disinfect exhibit surfaces after public hours, remove feces and food waste, replace bedding, ensure drains are clear, ventilate for thirty minutes, then mark the enclosure as cleaned in the maintenance log before animals return.
Appliance Repair Home — Maintain records of maintenance interventions
Record today's visits: log serial numbers, fault codes, parts fitted and hours worked for 12 Willow Road and 48 Maple Street, attach photos of faulty components, flag any warranty claims and submit the signed maintenance reports by close of business.
Appliance Repairer — Maintain records of maintenance interventions
Update the maintenance log for 18 Jun: record each intervention at 12 Pine Street and 7 Oak Avenue, list replaced parts with part numbers, note hours spent and warranty status, attach the customer signatures and photos, and submit the completed reports before end of shift.
Ar Vr Developer — Maintain and update existing software
Plan the maintenance sprint to update the AR headset client: list required bug fixes, API migrations, performance hotspots to profile, backward-compatibility tests, and assign owners so the release candidate ship date stays Monday.
Arborist — Clean, sharpen, and lubricate tools and equipment.
Clean, sharpen, and lubricate the chainsaw, pole saw, and hand saw after today’s job, follow the manufacturer torque and sharpening specs, replace any worn chain links, log parts replaced and service time in the maintenance record.
Arson Investigator — Conduct internal investigation to determine negligence and violation of laws and regulations by fire department employees.
Conduct an internal inquiry into the April ladder maintenance lapse: interview the crew on duty, collect their training records and the maintenance logs, establish whether policy or negligence occurred, and deliver a factual report with recommended discipline or retraining within two weeks.
Audio Technician — Perform minor repairs on equipment
Inspect the faulty mixer, replace the cracked channel fader and two loose RCA sockets, test each input and output with headset and line generator, log parts used in the maintenance book, and report safety checks to Facilities before closing the job today.
Perform the basic maintenance on the Peugeot 308 due Friday: change engine oil and filter, top up coolant and screenwash, check tyre pressures and tread, lubricate hinges, record odometer and create a follow-up note if any wear items exceed threshold.
Every job keeps its own logs, files, records and schedules — and the same one can live in hundreds of jobs, meaning something different in each. The LLOS Work Atlas maps them from the evidence — the software each career is attested to use — never from imagination.